Cisco 352-001 ExamCCDE Written Exam

Total Question: 501 Last Updated: Oct 11,2018
  • Updated 352-001 Dumps
  • Based on Real 352-001 Exams Scenarios
  • Free 352-001 pdf Demo Available
  • Check out our 352-001 Dumps in a new PDF format
  • Instant 352-001 download
  • Guarantee 352-001 success in first attempt
Package Select:

Questions & Answers PDF

Practice Test Software

Practice Test + PDF 30% Discount

Price: $65.95 $29.99

Buy Now Free Trial

Top 10 guidance 352-001 for customers (131 to 140)

It is impossible to pass Cisco 352-001 exam without any help in the short term. Come to Ucertify soon and find the most advanced, correct and guaranteed Cisco 352-001 practice questions. You will get a surprising result by our Down to date CCDE Written Exam practice guides.

Q131. Which two options are characteristics of firewall transparent mode operations in a firewall solution design? (Choose two.) 

A. The firewall acts like a router hop in the network. 

B. OSPF adjacencies can be established through the firewall. 

C. Changes in the existing IP addressing and subnets are required. 

D. Multicast traffic can traverse the firewall. 

E. The firewall can participate actively on spanning tree. 

Answer: BD 


Q132. Which statement about the behavior of OSPF on a hub-and-spoke topology is true? 

A. Additional host routes are added to the routing table on a NBMA network type. 

B. The DR and BDR election occurs regardless of the underlying OSPF network type. 

C. The DR election is a challenge unless a point-to-point network type is used. 

D. Traffic does not need to traverse the hub to reach the spokes. 

Answer:


Q133. You work as a network designer for a company that is replacing their Frame Relay WAN with an MPLS VPN service, where the PE-to-CE routing protocol is BGP. The company has 3000 routes in their distribution routers, and they would like to advertise their access routers through the MPLS network. Their service provider, however, only supports 1000 prefixes per VRF. Which two design solutions can be applied to ensure that your access routers will be able to reach all devices in your network? (Choose two.) 

A. Use prefix lists on your distribution routers to control which routes are sent to the MPLS network. 

B. On your distribution routers, configure null routes and aggregate routes for the prefixes in your network. 

C. Configure your distribution routers to send a default route to the MPLS network. 

D. Summarize the routes on the MPLS WAN interfaces of your distribution routers. 

Answer: BC 


Q134. You have been asked to design a high-density wireless network for a university campus. Which three principles would you apply in order to maximize the wireless network capacity? (Choose three.) 

A. Increase the number of SSIDs to load-balance the client traffic. 

B. Choose a high minimum data rate to reduce the duty cycle. 

C. Make use of the 5-GHz band to reduce the spectrum utilization on 2.4 GHz when dual-band clients are used. 

D. Enable 802.11ag channel bonding on both 2.4 GHz and 5 GHz to increase the maximum aggregated cell throughput. 

E. Use directional antennas to achieve better sector separation channel reuse. 

F. Implement a four-channel design on 2.4 GHz to increase the number of available channels. 

Answer: BCE 


Q135. Refer to the exhibit. 

In this network design, where should summarization occur to provide the best summarization and optimal paths during a single-failure incident as well as during normal operation? 

A. a single identical summary for all the branch offices placed on routers 1A, 1B, 2A, and 2B 

B. two summaries on 1A and 1B, and two summaries on 2A and 2B 

C. a single identical summary on 3A and 3B 

D. a single summary on each aggregation device for the branches connected to them 

Answer:


Q136. The network administrator of a branch office network has decided to deploy Unicast RPF at the access layer. He insists that the design must guarantee that all the packets arriving on the router interfaces are assigned to the same interface subnet. 

Which mode of Unicast RPF would you recommend as the lead network designer? 

A. uRPF strict mode 

B. uRPF loose mode 

C. uRPF VRF mode 

D. RPF feasible mode 

Answer:


Q137. A green data center is being deployed and a design requirement is to be able to readily scale server virtualization. Which IETF standard technology can provide this requirement? 

A. Transparent Interconnection of Lots of Links 

B. fabric path 

C. data center bridging 

D. unified fabric 

Answer:


Q138. Which mechanism should be added to a network design to identify unidirectional Spanning Tree Protocol failures through BPDU loss? 

A. UDLD 

B. loop guard 

C. BPDU guard? 

D. root guard 

Answer:


Q139. You are designing an optical network. Your goal is to ensure that your design contains the highest degree of resiliency. In which two ways will you leverage a wavelength-switched optical network solution in your network design? (Choose two.) 

A. a wavelength-switched optical network assigns routing and wavelength information 

B. a wavelength-switched optical network takes linear and nonlinear optical impairment calculation into account 

C. a wavelength-switched optical network guarantees restoration based strictly on the shortest path available 

D. a wavelength-switched optical network eliminates the need for dispersion compensating units in a network 

Answer: AB 


Q140. You have been asked to establish a design that will allow your company to migrate from a WAN service to a Layer 3 VPN service. In your design, you are keeping some WAN links between critical sites as a backup for this service. You plan to use OSPF as your IGP and BGP for the PE-CE protocol. When the Layer 3 VPN service is available, how will you prevent transit traffic over the backup links? 

A. Redistribute routes at the CE as external type 1. 

B. Redistribute routes at the CE as external type 2. 

C. Use conditional advertisement only when the Layer 3 service is down. 

D. Manually turn off the backdoor link when the Layer 3 service is up. 

Answer:


Related 352-001 Articles